董平川,牛彦良,李莉,沈晓英
DONG Ping-chuan1,NIU Yan-liang1,2,LI Li1

• 1:中国石油大学石油工程教育部重点实验室
• 2:中国石油大学石油工程教育部重点实验室
• 3:中国石油大学石油工程教育部重点实验室
• 4:国家知识产权局专利局 北京102249

摘要(Abstract)：

射孔是造成套管损坏的重要原因之一,建立了射孔套管的有限元力学模型,采用弹塑性有限元法,分别对螺旋布孔射孔套管采用不同的射孔孔径、射孔密度和射孔相位给套管强度造成的影响进行了模拟和分析。分析了不同孔径、孔密及相位角的射孔套管在外挤压力作用下的孔眼应力集中系数的变化规律。结果表明,射孔后套管的极限承载能力均有不同程度的下降,下降幅度与射孔密度有关,射孔后套管内的应力随射孔孔径、射孔密度和射孔相位的增加而增大,并使套管的抗拉、抗压强度降低。因此,在套管柱设计时应该考虑射孔的影响。最后,通过对几种布孔方案进行对比分析,找出了射孔套管的优选布孔方案。为射孔完井优选设计提供了合理的模型,为射孔段套管柱的合理设计提供了承载能力计算的可靠依据。
One of important cause of casing damage is casing perforation.Finite element mechanical model of perforated casing is established,and effect of perforating on casing strength,especially influence of perforation diameter,perforation density and perforation phase angle on casing strength is studied by using elastic and plastic finite element numerical modeling method.Under outer pressure condition,finite element analysis of stress concentration co-efficient in perforated casing is studied with different perforation diameter,perforation density and phase angle.Results of numerical modeling show that strength of casing reduces with perforation density,and that stress in perforated casing increases with the increase of above-mentioned perforating parameters,resulting in decrease of tensile strength and compression strength.Thereform effect of perforation should be considered in design of casing string.Optimized scheme for holding perforation is identified by comparing different schemes for holding perforation.Analysis result provides reasonable model for optimization design of perforating well completion and reliable foundation of sustainability computation for reasonable design for perforating sections of casing.

关键词(KeyWords)： 螺旋布孔;射孔套管;应力集中系数;套管强度;弹塑性有限元法
helix distributin perforation;perforating casing;stress concentration co-efficient;casing strength;elastic and plastic finite element method

Abstract:

Keywords:

基金项目(Foundation): 国家自然科学基金项目(编号50574059和50004002)

作者(Author): 董平川,牛彦良,李莉,沈晓英
DONG Ping-chuan1,NIU Yan-liang1,2,LI Li1

参考文献(References)：

• [1]张先普,陈继明.我国油田套管损坏的原因探讨[J].石油钻采工艺,1996,18(5):7-12.Zhang Xian-pu,Chen Ji-ming.Discussion on causes of casing failurein oilfields[J].Oil Drilling&Production Technology,1996,18(5):7-12.
• [2]王志信,蔡景瑞.射孔对套管的损害及改进措施[J].测井技术,1984,8(5):33-37.Wang Zhi-xin,Cai Jing-rui.The casing damage of perforation and itsinnovative approach[J].Well Logging Technology,1984,8(5):33-37.
• [3]王德良.中原油田套管损坏原因分析及预防[J].石油钻探技术,2003,31(2):36-37.Wang De-liang.Reasons and Analysis of Casing Damage in ZhongyuanOilfield[J].Petroleum Drilling Techniques,2003,31(2):36-37.
• [4]Godfrey W K,Methuen N E.Casing damage caused by jet perforating[R].SPE 3043,1970.
• [5]宗幼芄.油层射孔段套管抗挤能力的实验研究[J].石油学报,1988,9(4):84-96.Zong You-wan.The experimental study on the Mechanical Crush Resist-ance of Casing in the perforating oil formation[J].Acta Petrolei Sin-ica,1988,9(4):84-96.
• [6]King G E.The Effect of high-Density Perforating on the MechanicalCrush Resistance of Casing[R].SPE18843,1989.
• [7]Fereidoun A,Parfitt S H.A Simple Model for Collapse and Post-Col-lapse Behavior of Tubulars with Application to Perforated and SlottedLiners[J].Drilling&Completion,1998:190-196.